Replacement fuel pump

For models with the fuel pump mounted external to the fuel tank. No longer available new from Guzzi. Also known as Guzzi ref. 29107261 and 29107260

 2 in stock

 01107231 GU01107231 01 10 72 31
 0110 7231 0110.7231 01.10.72.31

One piece rear disc.

Note that this brake disc has 12mm ID mounting holes, you may require bushes if using 8mm bolts. Also known as Guzzi ref. 37635705, 30635731. Always fit new brake pads when replacing a brake disc - BRA27611 or BRA11498

 This part is available by special order, request a quote

 30635701 GU30635701 30 63 57 01
 3063 5701 3063.5701 30.63.57.01

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 This part is due back in stock soon, call 01484 841395 to reserve yours

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

22 teeth 3rd gear for gearbox layshaft. Helical 3rd gear

 This part is available by special order, request a quote

 14214810 GU14214810 14 21 48 10
 1421 4810 1421.4810 14.21.48.10

Deep sump spacer made from alloy. This increases the volume of air in the crankcase and helps reduce 'heavy breathing'. The oil is also better cooled when using one of these. Finished externally in silver paint

To fit this sump spacer you will need longer sump bolts (14 x SSA06055 + 4 x SSA06090) and a pair of sump gaskets (ENA14036). You will also need a longer dipstick, see ENA28005

 Availability varies on this part, check availability

 14003240 GU14003240 14 00 32 40
 1400 3240 1400.3240 14.00.32.40

6 dog 28 tooth 5th gear

 This part is available by special order, request a quote

 14122013 GU14122013 14 12 20 13
 1412 2013 1412.2013 14.12.20.13

Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 1 in stock

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Output flange for drive box, engages with the driveplate on the wheel

Also known as Guzzi ref. 17351401. 8 hole M8 fixing in flange

 This part is available by special order, request a quote

 17351400 GU17351400 17 35 14 00
 1735 1400 1735.1400 17.35.14.00

Set of 3 piston rings for Nikasil 92mm bore

Only for Cali 1100 frame prefixes KC and KD, for KG and KH prefixes see ENA18601

 This part is available by special order, request a quote

30060660-z 30060660 GU30060660 30 06 06 60
 3006 0660 3006.0660 30.06.06.60

Timing sensor for ignition and tacho

3 pin block connector. Used on models with the smaller 15M ECU

 2 in stock

 01721600 GU01721600 01 72 16 00
 0172 1600 0172.1600 01.72.16.00